Many people believe that as long as the material of the 3A manual sanitary diaphragm valve is up to standard and certified, it can guarantee the sanitary level of the production line. However, this is not the case. Whether the valve installation of food, medicine and pure water pipeline is standard or not directly determines the cleanliness and sterilization effect of the entire pipeline. The same SS304/SS316, 3A certified diaphragm valve, if installed correctly, can meet CIP and SIP cleanliness requirements for a long time. Incorrect installation can lead to dead ends, material accumulation, water accumulation, bacteria, and failure of GMP and 3A hygiene standards. In this paper, the core installation points of 3A manual sanitary diaphragm valves are explained in detail to help engineers avoid common hazards.
The most important installation principle is the prohibition of reverse installation and random installation. The sanitary diaphragm valve fluid direction is strict, the valve body flow pipeline design is streamlined, does not have the dead angle. Factory valve body will be engraved with flow arrows. Many builders reverse install valves to adjust to the angle of the pipe, the deadliest mistake in cleaning pipes. Reverse installation will result in a puddle and material retention areas inside the valve body, preventing the cleaning solution from fully rinsing the inner wall of the valve cavity. CIP cleaning residues and steam sterilization are not thorough, leading to long-term accumulation of protein, sugar and liquid residues, which directly results in microbial exceedance and product contamination, completely undermining cleanliness level. Before installation, the direction of the valve must be checked to ensure that the arrow of the valve is in perfect alignment with the direction of the medium.
Then there's the pipe docking installation specification, which is one of the most overlooked details. 3. sanitary grade diaphragm valve is usually connected with a fast installation chuck. During installation, the chuck washer must be placed in the middle, aligned and smooth, and must not be deflected, squeezed or suspended. The eccentric compression of the gasket will form prominent steps that will easily allow the material to accumulate on the wall and become a blind spot for cleaning. At the same time, the use non-standard thick gaskets and inferior rubber gaskets prohibited. Thickness is too large, can cause the connection is not uniform, destroy the overall fluency of pipeline, does not meet the 3A dead-angle design standard. When installing fixtures, the force should be uniform and moderate. If the valve is too loose, bacteria can leak and accumulate, and if the valve is too tight, it can compress diaphragm deformation, affecting the sealing and service life of the valve.
There are also strict requirements for the installation posture of the valve body, which directly affects the valve's ability to drain and clean itself. Priority should be given to vertical installation of clean pipeline valves with valve stem facing upwards to ensure that the medium inside the closed chamber can be completely drained by artesian flow without any residual water accumulation. In many sites, valves are installed horizontally and diagonally for ease of construction, resulting in water accumulation at the bottom of the chamber. The lingering effects of residual water can breed bacteria and produce biofilms that can be potentially cleaning hazards even if often disinfected. For working conditions that require horizontal installation, ensure that the valve body flow channel is smooth and does not sink, leaving a reasonable slope of the pipe and eliminating dead ends of fluid accumulation.
At the same time, installation error caused by pipeline stress should be avoided. During installation, it is strictly forbidden to force tug or twist the pipe hard docking valve. Many workers forcibly twist the valve body to align the pipe mouth, causing the valve diaphragm to shift and the valve body to deform. In the short term, the installation of the valve seems to have been completed, but in reality, the sealing structure has been damaged, prone to micro-leakage, lax closure, internal structure of the valve cavity, such as dislocation, forming a hidden dead angle. The correct approach is to secure the pipe, fine-tune alignment, and then secure the valve to ensure that the body is not squeezed by external stress and to protect the core seal structure.
In addition, the installation of a clean environment must comply with dust-free construction requirements. 3A sanitary valve is produced in a sterile and clean state. After opening the box, it is forbidden to touch the inner wall of the valve body and the sealing cover with your bare hands to prevent fingerprints, oil stains and dust residue. Installation tools need to be cleaned and disinfected in advance and installed quickly and in a standardized manner to avoid prolonged exposure of the valve body to airborne dust and impurities. After installation, piping must be blown, pressurized, cleaned and sterilized to ensure no leakage, no dead angle and thorough drainage before production.
Taken together, the cleanliness of 3A manual sanitary diaphragm valves depends on the quality of seven parts and standardized installation of three parts. Reverse installation flow direction, gasket dislocation, incorrect installation posture and forced stress docking can lead to the complete loss of the cleaning advantage of compliant 3A valves and become a hazard to pipeline hygiene. We should strictly follow installation standard, control every detail, give full play to the advantages of dead-angle, easy to clean and disinfect, maintain the production line clean and ensure the production safety.
